Giant 1-Feb Manual do Utilizador

CHAPTER Installing and Starting Up the Hub 2-12Installing and Starting Upthe HubThis chapter provides installation warnings, guidelines, requirements,

Installing the Hub in a RackFastHub 400 10/100 Series Installation and Configuration Guide2-10Attaching the Hub to the RackAfter the brackets are atta

Installing and Starting Up the Hub 2-11Attaching the Cable Guide to the BracketAttaching the Cable Guide to the BracketAttaching the cable guide and

Installing the Hub on a WallFastHub 400 10/100 Series Installation and Configuration Guide2-12Installing the Hub on a WallThis section describes how t

Installing and Starting Up the Hub 2-13Attaching the Hub to a WallAttaching the Hub to a WallFor the best support of the hub and cables, make sure th

Connecting to the Console Port (FastHub 400M Models)FastHub 400 10/100 Series Installation and Configuration Guide2-14Connecting to the Console Port (

Installing and Starting Up the Hub 2-15Connecting to the Console Port (FastHub 400M Models)Step 2 Connect one end of the supplied rollover console ca

Assigning IP Information to the Hub (FastHub 400M Models)FastHub 400 10/100 Series Installation and Configuration Guide2-16Assigning IP Information to

Installing and Starting Up the Hub 2-17Assigning IP Information to the Hub (FastHub 400M Models)Step 5 Enter the IP address of the default gateway (f

Connecting to the 10/100 Network Ports and Uplink PortFastHub 400 10/100 Series Installation and Configuration Guide2-18Connecting to the 10/100 Netwo

Installing and Starting Up the Hub 2-19Connecting to the 10/100 Network Ports and Uplink Port• Connectingtodevicesthatdonotautonegotiate or that have

WarningsFastHub 400 10/100 Series Installation and Configuration Guide2-2WarningsTranslated versions of the following safety warnings are provided in

Accessing the Management Interfaces (FastHub 400M Models)FastHub 400 10/100 Series Installation and Configuration Guide2-20Step 2 Connect the other en

Installing and Starting Up the Hub 2-21Accessing the FastHub 400 Series Hub ManagerAccessing the FastHub 400 Series Hub ManagerTo access the hub mana

Accessing the Management Interfaces (FastHub 400M Models)FastHub 400 10/100 Series Installation and Configuration Guide2-22Figure 2-10 Home PageNote Y

Installing and Starting Up the Hub 2-23Accessing the CLIAccessing the CLIYou can access the CLI• From a console terminal connected to the hub console

Accessing the Management Interfaces (FastHub 400M Models)FastHub 400 10/100 Series Installation and Configuration Guide2-24• CISCO-SIBU-MANAGERS-MIB.m

Installing and Starting Up the Hub 2-25Accessing the MIB Files through SNMPUsing CCO to Access the MIB FilesTo access the MIB files from CCO, click So

Where to Go NextFastHub 400 10/100 Series Installation and Configuration Guide2-26Where to Go NextNow that you have installed the hub and, if you have

Installing and Starting Up the Hub 2-3EMC Regulatory StatementsWarning This equipment is intended to be grounded. Ensure that the host is connected t

Installation Guidelines and RequirementsFastHub 400 10/100 Series Installation and Configuration Guide2-4Installation Guidelines and RequirementsWhen

Installing and Starting Up the Hub 2-5Package ContentsPackage ContentsEach hub is shipped with the following items:• FastHub 400 10/100 Series Cablin

Powering Up the Hub and Running POSTFastHub 400 10/100 Series Installation and Configuration Guide2-6Powering Up the Hub and Running POSTBefore instal

Installing and Starting Up the Hub 2-7Installing the Hub on a Table or ShelfInstalling the Hub on a Table or ShelfTo install the hub on a table or sh

Installing the Hub in a RackFastHub 400 10/100 Series Installation and Configuration Guide2-8Installing the Hub in a RackThis section describes how to

Installing and Starting Up the Hub 2-9Attaching the Brackets to the HubFigure 2-2 Attaching Brackets for 19- and 24-inch Racks (Rear Panel Forward)Fi